Home > How To > How To Setup Raid 1 Windows 10

How To Setup Raid 1 Windows 10


This can sometimes help with drive letter problems. Ignore this screen by choosing "Next" one more time: 7) In "Task Selection" screen, select "Drivers" and "Bootable ISO" by pressing corresponding buttons. When I perform a setup from the XP CD and specify either the SATA or the RAID Driver, when the setup process comes to check the hard drives, again it hangs It mentions how to install XP to RAID-1 and RAID-0 configurations.It does NOT specifically mention installing XP to one HD with no RAID configuration. weblink

I : - Updated my BIOS to the latest version (1009.001, September 13th 2005 release) - Re-created my RAID array using the F10 utility - Installed Windows XP using a special Umoms really needs to read the entire section on RAID arrays (starting with p.256), as he/she never mentioned using the preboot RAID utility (F12 method). Note: Before configuring a software RAID array, it is important to note that Windows 2000/XP cannot run from the software RAID. RAID 1 offers no gain in drive performance. http://superuser.com/questions/304620/installing-windows-xp-pro-on-a-raid-1-array-without-the-driver-floppy

How To Setup Raid 1 Windows 10

Once you have Windows again you will use the raid utility to disable the mirroring, then you will be able to set up using 2 different drives. Q: Do I need to tweak anything in BIOS setup? You will be prompted: “After you convert these disks to dynamic, you will not be able to start other installed operating systems from any volume on these disks. What is AHCI/RAID drivers?

I thought it would be easier to follow in line.2. don't be discouraged. If I re-enable the F10 BIOS, it will just complain that it can't to RAID with one disk. Windows 7 Raid 1 Set SATA mode to RAID, Setup new RAID 0 Volume on 2 128 SSDs, Start Windows install, after first screen get following error message: Required CD/DVD drivers not found If I

To test this, remove the Maxtor from the machine. The process is explained in detail in this article. 6. C:\) onto other disks. Powered with <3 from Vanilla & WordPress.

I even switched the Boot Priority. How To Setup Raid Windows 10 When I set mine up I simply disabled the ones not being used for the XP install and enabled them after it was done. 0 TheBaron Austin, TX May 2005 edited By the way, during the course of the eight hours I have spent on this problem I also discovered that: i) It appears to make little difference which version of the Right-click on Disk 1 and select Initialize DiskIn the Computer Management window right-click on either Disk 0 or Disk 1 and select Convert to Dynamic Disk… see the screen capture "ToDynamic.jpg"Make

How To Setup Raid 0

RacWiscoFeb 16, 2012, 8:56 AM Brand new build. https://www.cnet.com/forums/discussions/installing-windows-xp-on-a-raid-system-248182/ If you have a 64 Bit Version of Windows you would need the 64 Bit Drivers. How To Setup Raid 1 Windows 10 Q: It's still not detected. How To Setup Raid 0 Windows 10 Troubleshooting If you have problems integrating SATA/AHCI drivers into Windows XP, read this section.

Just an idea... have a peek at these guys Modern disks have Serial ATA (SATA) interface, old generation of disks had ATA interface. Ask ! This must be enabled. Windows 10 Raid

Only use DP to slip drivers, do not use Nlite for this task. So I... - Enabled RAID in the BIOS for a SINGLE DRIVE then installed XP then installed the standalone drivers - Reboot, enabled RAID in the BIOS for my SECOND DRIVE Once reported, our moderators will be notified and the post will be reviewed. check over here I have tried various drivers downloaded from ABIT, original Board drivers, but I have exactly the same effect on them all, so at the moment I am running on the Stock

Any ideas what could be problem here? 17 answers Last reply Feb 19, 2012 More about problem windows install raid array jrazor247Feb 16, 2012, 10:33 AM Could you please tell us Windows 7 Raid 0 Start with clean unmodified Installation files when using DP for best results share|improve this answer answered Jun 30 '11 at 20:13 Moab 47k977129 Thanks, I'll give this a look. The correct model is Toshiba Qosmio G25-AV513.

Windows 7 Home allows JBOD and RAID 1 while Professional and Ultimate add RAID 0 mirroring.

J Petz 0 JannPadley Jul 2005 edited Jul 2005 The drive letters are associated with volumes (things can potentially be used as drives) in the registry at HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices On a simple The system returned: (22) Invalid argument The remote host or network may be down. Browse to the extracted NVIDIA 6.53\IDE\WinXP folder and select the NVRAID.INF file that is displayed. Windows 7 Raid 5 It has been reported that no matter what combination, be it either or both drivers at the F6 command...two drives appear when there should be one.

I may come back and update this if I miss a step. Anyway, I found the answer online. ii) Strangely I had no problem with an older copy of XPSP1 Professional. this content When I was trying to setup my RAID configuration I told myself this is the last thing I'd do but I was wrong.

I dunno...just to be difficult I guess. Can you? 0 profdlp The Holy City Of Westlake, Ohio Sep 2005 edited Sep 2005 stakenyf wrote: ...I can't tell whether I'm running a proper RAID array or not. If XP cannot see drives that are just standard, empty SATA disks (not enabled for RAID), then it has a more serious and lower level problem than activation. more info is always better by mark04276 / May 18, 2007 7:00 AM PDT In reply to: Redundant? 1.

This way works great for 3D video card drivers, sound drivers, network drivers etc. How was the red coat in Schindler's List created? No need to press F6. Im about ready to shelve it for a month and let other people be Crash Test dummies until they iron this POS out.

How to integrate F6 AHCI/RAID drivers into Windows XP installation disk / ISO file? I've tried umpteen combinations to get around this and here is what I've found as a possible solution. Go into nVIDIA BIOS and set it as RAID 0 (Striping). When I reboot my RAID array reads healthy but I can't tell weather I'm running a proper RAID array or not.

Perhaps it was the same error you were getting. It just keeps going back to booting from the CD even after the setup files have been copied. Most of the time Im forgetting things. Enable the RAID function.

Does Windows XP on the WD still boot up? So I conclude that the NVidia drivers are NECESSARY even if RAID is disabled in the BIOS.